Getting started with Arduino


	Our PriceHK$165.00 CodeBBR-0101-001 Stock 0 Weight 200 No reviews

Save wishlist

Add to comparison chart | Compare Products

This valuable little book offers a thorough introduction to the open-source electronics prototyping platform that's taking the design and hobbyist world by storm. Getting Started with Arduino gives you lots of ideas for projects and helps you get going on them right away. To use the introductory examples in this book, all you need is a USB Arduino, USB A-B cable, and an LED. This 128-page book is a greatly expanded follow-up to the author's original short PDF that's available on the Arduino website.

Editorial Reviews

Amazon.com Review

Getting Started with Arduino, authored by Arduino co-founder Massimo Banzi, offers a brief, fun, and lucid overview of Arduino that will appeal to lots of people who've been wanting to get into physical computing and want a way in. This handy little guide should be just the ticket. To work with the introductory examples in this book, all you need is a USB Arduino, USB A-B cable, and an LED.

The Arduino Platform
Arduino is composed of two major parts: the Arduino board, which is the piece of hardware you work on when you build your objects; and the Arduino IDE, the piece of software you run on your computer. You use the IDE to create a sketch (a little computer program) that you upload to the Arduino board. The sketch tells the board what to do.
Not too long ago, working on hardware meant building circuits from scratch, using hundreds of different components with strange names like resistor, capacitor, inductor, transistor, and so on.
Every circuit was "wiredÃƒÂ¢€Ã‚Â to do one specific application, and making changes required you to cut wires, solder connections, and more.
With the appearance of digital technologies and microprocessors, these functions, which were once implemented with wires, were replaced by software programs.
Software is easier to modify than hardware. With a few keypresses, you can radically change the logic of a device and try two or three versions in the same amount of time that it would take you to solder a couple of resistors.

The Arduino Hardware
The Arduino board is a small microcontroller board, which is a small circuit (the board) that contains a whole computer on a small chip (the microcontroller). This computer is at least a thousand times less powerful than the MacBook IÃƒÂ¢€Ã¢â€žÂ¢m using to write this, but itÃƒÂ¢€Ã¢â€žÂ¢s a lot cheaper and very useful to build interesting devices. Look at the Arduino board: youÃƒÂ¢€Ã¢â€žÂ¢ll see a black chip with 28 "legsÃƒÂ¢€Ã‚ÂÃƒÂ¢€Ã¢€Âthat chip is the ATmega168, the heart of your board.
We (the Arduino team) have placed on this board all the components that are required for this microcontroller to work properly and to communicate with your computer. There are many versions of this board; the one weÃƒÂ¢€Ã¢â€žÂ¢ll use throughout this book is the Arduino Duemilanove, which is the simplest one to use and the best one for learning on. However, these instructions apply to earlier versions of the board, including the more recent Arduino Diecimila and the older Arduino NG. The figure on the left below shows the Arduino Duemilanove; The figure on the right shows the Arduino NG.

Product Description

This valuable little book offers a thorough introduction to the open-source electronics prototyping platform that's taking the design and hobbyist world by storm. Getting Started with Arduino gives you lots of ideas for Arduino projects and helps you get going on them right away. From getting organized to putting the final touches on your prototype, all the information you need is right in the book.

Inside, you'll learn about:

Interaction design and physical computing
The Arduino hardware and software development environment
Basics of electricity and electronics
Prototyping on a solderless breadboard
Drawing a schematic diagram

And more. With inexpensive hardware and open-source software components that you can download free, getting started with Arduino is a snap. To use the introductory examples in this book, all you need is a USB Arduino, USB A-B cable, and an LED.

Join the tens of thousands of hobbyists who have discovered this incredible (and educational) platform. Written by the co-founder of the Arduino project, with illustrations by Elisa Canducci, Getting Started with Arduino gets you in on the fun! This 128-page book is a greatly expanded follow-up to the author's original short PDF that's available on the Arduino website.